We carry a wide range of accessories for your mini mill, including boring heads, collet sets, clamping kits, DROs, end mill holders, and fly cutters.
|
This arbor has a soft end which can be machined to suit your purpose.
The arbor has a case hardened 3 Morse taper shank and is threaded for a 3/8-16 NC drawbar.
The machinable end is 1.5" long and 1.5" in diameter.
|
|
- For blades with 1" diameter arbor holes.
- TTS-ATC Groove Geometry
- Projected length is 2.6" from spindle nose
|
|
- 3MT Shank
- 7/8"-20 Mounting Thread
- Tapped for 3/8" -16 Drawbar
- Made of high grade tool steel
- Hardened and ground
|
|
- MT3 shank, 7/8"-20 mounting thread
- Tapped for 3/8"-16 drawbar
- Made of 20CrMnTi alloy steel
- Electrolysis nickel coating
- Superior craftsmanship
|
|
- R8 Boring Head Shank
- 7/8"-20 Mounting Thread
- Tapped for 7/16"-20 Drawbar
- Made of high grade tool steel
- Hardened and ground
|
|
- R8 shank, 7/8"-20 mounting thread
- Tapped for 7/16"-20 drawbar
- Made of 20CrMnTi alloy steel
- Electrolysis nickel coating
- Superior craftsmanship
|
|
- 2" boring head holds 1/2" shank boring bars
- The mill boring head offsets up to 5/8"
- Mounts on a shank with a 7/8"-20 thread
- Dial is graduated in 0.001"
- Bar holder moves freely and smoothly
|
|
- 2" diameter boring head holds 1/2" shank boring bars
- The boring head offsets up to 5/8"
- Mounts on a shank with a 7/8"-20 thread
- Dial is graduated in 0.001"
- Boring bar holder moves freely and smoothly
|
|
- Milling machine chip shield uses strong Neodymium magnets to mount to the front or back of a machine
- Conveniently remove without the hassle of fussing with tools or screws
- Adjustable friction hinges allow setting the side panels at any angle up to 150 degrees
- Compatible with any 3"- 4" milling vise with a flat surface on either end
- Approximate dimensions: 11 1/4" x 3 3/4" x 1/4"
|
|
- Metal chip tray, black
- 16.1" x 19.3" x 0.9" (410 mm x 490 mm x 24 mm)
- Fits SIEG X2 and SX2 mini mills
- Holes align for securing compatible mini mill
- Available in tray only or on a stand
|
|
- Nuts fit 3/8" T-Slots
- Stud thread: 5/16"-18
- 58 Pieces
- All parts are heat treated
- Storage rack included
|
|
|
- Nuts fit 7/16" (12 mm) T-Slots
- Stud thread: 3/8"-16
- 58 Pieces
- All parts are heat treated
- Storage rack included
|
|
- Stud thread: 3/8"-16
- T-slot width at top: 7/16" (12 mm)
- 58 Pieces
- All parts are heat treated
- Organizer case included
|
|
|
- Stud size: M6
- T-slot: 8 mm wide at top
- 58 pieces
- Made of heat treated steel
- Organizer case included
|
|
- For SIEG X2 class of 3 Morse Taper Mills
- 3/8"-16 thread
- For 3MT spindle
- 4" long when measured like a bolt
|
|
- For SIEG X2 family of 3 Morse Taper Mills
- M12 thread
- For 3MT spindle
- 4" long when measured like a bolt
|
|
- For SIEG X2, X2D and SX2 R8 Mills
- 7/16" - 20 thread
- For R8 spindle
- 4-3/8" long when measured like a bolt
|
|
- Set of 5 3 Morse taper end mill holders
- 3 Morse Taper Shanks
- Drawbar thread is 3/8-16
- Compatible with Mills with 3 Morse Taper Spindle
- For end mills with shanks 3/16", 3/8", 1/2", 5/8", and 3/4"
|
|
- Set of five R8 end mill holders from 3/16" to 3/4"
- R8 Shanks
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
- For end mills with shanks 3/16", 3/8", 1/2", 5/8", and 3/4"
|
|
- 1/2" Hole Diameter
- 3 Morse Taper Shank
- Uses a 3/8"-16 NC Drawbar
- Compatible with Mills with 3 Morse Taper Spindle
|
|
- 3/16" Hole Diameter
- 3 Morse Taper Shank
- Uses a 3/8"-16 NC Drawbar
- Compatible with Mills with 3 Morse Taper Spindle
|
|
- 3/4" Hole Diameter
- 3 Morse Taper Shank
- Uses a 3/8"-16 NC Drawbar
- Compatible with Mills with 3 Morse Taper Spindle
|
|
- 3/8" Hole Diameter
- 3 Morse Taper Shank
- Uses a 3/8"-16 NC Drawbar
- Compatible with Mills with 3 Morse Taper Spindle
|
|
- 5/8" Hole Diameter
- 3 Morse Taper Shank
- Uses a 3/8"-16 NC Drawbar
- Compatible with Mills with 3 Morse Taper Spindle
|
|
- 1/2" Hole Diameter
- R8 Shank
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
|
|
- 3/16" Hole Diameter
- R8 Shank
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
|
|
- 3/4" Hole Diameter
- R8 Shank
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
|
|
- 3/8" Hole Diameter
- R8 Shank
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
|
|
- 5/8" Hole Diameter
- R8 Shank
- Drawbar End Thread is 7/16"-20
- Compatible with Mills with R8 Spindle
|
|
Handles with molded plastic knobs for mini mill.
Three of these decorative red handles will dress up your mini mill.
|
|
- Cast iron handwheel with chrome plated finish
- Fits SEIG X2, SX2 and HiTorque Mini Mills
- 100 mm outside diameter
- Mounts on 10 mm shaft with a 4 mm keyway
- Bore is 23 mm, handle is included
|
|
- Thread is M6 x 1.0
- The threaded stud is approximately 20 mm long
- Handle is 40 mm long
|
|
Plastic oil can. This is the small plastic bottle that comes with the mini lathe and mini mill.
|
|
- Fits large-table mini mills
- Clutch disengages power feed when not in use
- Adjustable limit switches restrict travel
- 120-240V 50-60Hz
|
|
- Fits standard mini mills
- Clutch disengages power feed when not in use
- Adjustable limit switches restrict travel
- 120-240V 50-60Hz
|
|
- Fits X3 and SX3 Mills, Grizzly G0463 and G0619
|
|
- High Grade Tool Steel
- Drawbar End Thread Is 7/16"-20
- Length: 127 mm
- Diameter: 17.18 mm
- Adapter 2 Morse Taper to R8
|
|
- Hardened and Ground
- Drawbar End Thread Is 7/16"-20
- Adapts 3 Morse Taper to R8
|
|
- Provides a safe way to change cutting tools in R8 based tool holders.
- Easy assembly and installation.
- Mounts to the front slot of a mill table, workbench, or vise.
- Includes a tool caddy for quick access to frequently used tools
- Convenient for changing R8 based indexable-insert tooling
|
|
- Adds 2" (50 mm) to the head space
- For solid column mini mills and micro mills
- Includes proper mounting hardware
|
|
- Spindle lock and quill stock makes tool changes easier, faster, and more convenient
- Provides a quick and accurate way to set the quill depth of cut
- Made in precision machining centers in the U.S.A.
- Fits Grizzly G0704 mills
|
|
- Makes tool changes easier, faster, and more convenient
- When engaged, the plunger automatically drops into the locking hole as the spindle is rotated
- An electro-magnetic interlock disables power to the motor when the spring plunger is engaged
- Frees both hands for changing tools
- Loosen and tighten keyless chucks with one hand
|
|
- Metal stand and chip tray for mini mill
- Single column design
- 16.1" x 19.3" x 35.3" (410 mm x 490 mm x 896 mm)
- Cabinet for storage with locking door
- Fits the HiTorque and SIEG X2L/SX2L mini mills
|
|
- Metal stand and chip tray for mini mill
- Single column design
- 16.1" x 19.3" x 35.3" (410 mm x 490 mm x 896 mm)
- Cabinet for storage with locking door
- Fits SIEG X2 and SX2 mini mills
|
|
- Fits 12 mm T-slots
- Threaded M10
- Black oxide finish
- Heat treated 1040 steel, case hardened
- Fits T-slots measuring 0.46" to 0.54" in width
|
|
- Fits 7/16" (12 mm) T-slots
- Threaded 3/8"-16
- Black oxide finish
- Heat treated 1040 steel, case hardened
- Fits T-slots measuring 0.43" to 0.49" in width
|
|
- Plugs into control panel
- Mounts magnetically
- Displays to nearest 20 RPM of spindle
- Works for HiTorque mini mills and mini lathes
|
|
- Rigid stop for small milling machines
- Made of hardened steel
- Column is 0.47" diameter and 3.94" tall
- Base is 1.57" wide, 2.76" long and 0.47" thick
- Rod is 0.375" diameter and 6" long
|
Belt Drive Conversion Kit, Mini Mill
